How do articulation, contraction and expansion joints differ?
Articulation joints accommodate movement of the supporting structure. Contraction joints open as masonry shortens. Expansion joints close as masonry grows or associated concrete shrinks. A joint can perform more than one of these jobs, so its visible width does not identify the movement or explain a crack beside it.
A movement joint is put in deliberately so the wall does not have to crack in an uncontrolled place to accommodate the expected movement. The question is not simply whether the wall has a line in it. It is whether that line can move as intended, while the masonry on each side remains adequately supported and the joint still provides any required weather protection.
What makes the joint open or close?
Consider a wall that spans between parts of a footing that do not move together. If the masonry is continuous across the change in support, it has to distort to follow it. An articulation joint provides a planned break where adjoining panels can accommodate some relative movement. It reduces the risk of cracking from footing or other structural movement; it does not stop the footing from moving.
A contraction joint addresses shortening rather than growth. In concrete masonry, shortening can pull the two ends of a run away from each other at a planned joint. If the wall is restrained and cannot move there, a crack may open elsewhere instead. The contraction-joint provisions in AS 4773.2:2015 address unreinforced concrete and calcium-silicate masonry.
An expansion joint has the opposite job: it leaves room for the two sides to approach, as they do when clay masonry grows. If the same gap also serves as an articulation joint, the detail needs movement capacity for both functions. Its width at one inspection does not show how much of that capacity remains.
A crack beside a joint has several possible explanations. Rigid material inside the gap may obstruct closure. A continuous finish may crack across the line while the joint in the wall still moves. Movement of the supports may also produce damage independent of the visible joint. These explanations point to different work, and the pattern across the wall and its support helps distinguish them.
Follow the wall and its supports, not a spacing rule
Openings, changes in wall height or thickness, junctions between materials and joints in the supporting footing or slab all affect the layout. AS 4773.2:2015 distinguishes uninterrupted walls from walls with openings. Its joint provisions have since been amended; check the requirements applicable to the project rather than using the 2015 provisions as a spacing or cutting schedule for existing masonry.
AS 4773.2:2015 distinguishes reinforced masonry that relies on a continuous bond beam from masonry designed to articulate through the bond beam. A bond beam is a reinforced horizontal element. Cutting one intended to be continuous is a structural change. Near an opening, establish how the lintel supports the masonry before assuming a joint can be moved to the edge of the frame.
Leave room for movement without losing restraint
A mortar lump can stop part of an expansion or articulation gap from closing. A rigid render coat can transfer movement from a working joint into the finish and crack it. At a window or door, the clearance must allow the intended movement without sacrificing weatherproofing. Where applicable, retain the required fire and acoustic performance too. A hard patch, an open slot and a flexible sealed joint are not equivalent repairs.
A joint that relieves in-plane movement does not remove the need to restrain a wall against loads across its face. Ties that connect an unreinforced veneer to the frame or link the two leaves of cavity masonry are distinct from any sliding or flexible ties across the joint itself. The latter depend on the kind of wall and joint. A neatly sealed face reveals little about either form of restraint.
An intact flexible seal, a split through a coating and loose sealant around a frame may look like variations of the same line. They are not the same finding. For example, a coating split directly over a known joint warrants checking whether the surface detail can follow the movement. It does not establish that the masonry has split behind it. Do not dig into an unknown detail to find out.
Decide what the proposed repair would change
Compare the visible joint with the wall layout, the nearest opening and any history of filling or recoating. If a window has also begun binding, establish whether the available frame clearance has closed or whether the opening itself has distorted. Replacing a weather seal and correcting a support or restraint issue are different jobs; one cannot be specified from the appearance of the other.
Do not saw a new joint, inject an old one or rigidly bridge it to hide the line. Establish the intended movement, the support and ties on each side, and which sealing or other performance the repaired detail must retain.