What should be checked before cutting a chase or hole in masonry?

Before cutting a chase, hole or recess in masonry, establish what the wall carries or restrains and locate the proposed cut relative to its supports, reinforcement, fixings and moisture details. Both the size and the position matter. A small hole that interrupts a fixing or penetrates a cavity flashing can cause a problem that a larger opening in a separately designed location would avoid. Determine the required assessment before choosing where the service goes.

Where the construction standard stops

AS 4773.2:2015 clauses 10.9 and 11.8 address cavity masonry and unreinforced single-leaf masonry respectively, but do not cover the detailing of chases, holes and recesses. They refer specified cases to AS 3700 for design and detailing, with different descriptors for chases and for holes or recesses. That referral does not make a smaller cut automatically safe near a bearing, wall edge, tie or previous opening.

A chase removes a strip of wall, a penetration goes through it, and a recess locally reduces the section even if it does not go through. They can have different effects despite taking the same volume of material. For example, a long horizontal chase across the narrow masonry between openings can affect a continuous strip where forces travel through the wall. A hole close to a lintel bearing can reduce material carrying a concentrated reaction without reducing much of the whole wall's area.

A veneer leaf need not carry a floor or roof, but it still needs ties, support and moisture protection. In cavity masonry, identify which leaves are affected; reaching the second leaf can interrupt a different function. In reinforced masonry, bars are concealed in grouted cavities or cores, including horizontal bars in bond beams. A shallow cut can remove part of the face shell or grout even if it does not sever a bar. Conversely, bed-joint mesh alone does not identify reinforced masonry within AS 4773.2:2015.

A route at an opening can also cross a flashing or remove part of a weather-resistant face. In the cavity masonry provisions, penetrations through cavity flashing receive specific treatment to maintain the moisture detail. Clearance for the pipe is only one part of the problem; the cavity should still collect and discharge water where intended.

Can the service follow a route that avoids the critical detail?

Show the service on a plan and elevation, with its proposed position, direction and anticipated depth. Mark each change of direction and its relationship to window heads or sills, returns, piers, wall tops and known connection lines. Note existing holes or recesses, even if they are on the other face. The designer needs to see what remains between cuts, not only the area removed by the new one. Checking a route at a clear wall bay does not establish that the same path is suitable where it crosses a pier or an opening.

For example, a pipe route that looks short from inside may cross the masonry immediately below a window, where a flashing or another built-in component may need to continue beyond the opening. A planned route outside that junction may avoid disturbing its drainage. In another case, an existing service zone or a surface-mounted route could avoid having to resolve concealed reinforcement. These are choices to compare before drilling, not conclusions about what any unseen wall contains.

Use available project sections and construction photographs to identify the wall type and any reinforced cores, existing services and accessories before deciding what must be examined on site. If the evidence does not show the actual positions, the next decision is whether to verify them by an appropriate method or move the route. A drawing might show a bond beam at the wall head without establishing the direction of a later service installed below it. The construction left by an exploratory cut cannot serve as the evidence that it was safe to make.

If the wall has already been cut, assess what remains

Show the whole wall as well as the cut. Capture where it stops in relation to a support or opening, what material is visible at the edge and whether associated cracking appeared before or after the work. Record which face has been cut and any known work on the other face. If the depth or reinforcement is not visible, mark it unknown; do not enlarge the cut to investigate. A photo of exposed metal alone cannot show whether the bar remains continuous beyond the opening.

Also note signs of a former opening or patched recess around the proposed route. Mortar or a finish may make those areas look continuous, while the size and condition of any infill remain unknown. It may matter if the new opening would leave a narrow strip between the old cut and a visible pier, even though the cuts never overlap.

An assessment can then separate a structural problem, a disrupted moisture path and damage confined to a finish. A neat infill may hide the original loss of wall section without restoring reinforcement or drainage. Before specifying the repair, determine which function was affected, what remains intact and how the proposal will restore the relevant detail.